Share with your friends!

When your baitcaster drag not working, it can be frustrating and even dangerous. There are a few things that could be causing the problem, and thankfully, there are a few easy solutions.

One of the most common reasons for a baitcaster’s drag not to work is because the spool isn’t level. This can happen if you bump the reel or if it’s not properly secured on the rod.

To fix this, simply open the baitcaster and check that the spool is level. If it’s not, use a Phillips head screwdriver to adjust the screws until it is.

Another common reason for a baitcaster’s drag to fail is because the line isn’t wound correctly. This can cause the line to get tangled and ultimately break.

To fix this, simply re-wind the line following the proper instructions for your particular reel.

Finally, if your baitcaster’s drag still isn’t working after trying these two solutions, it’s possible that the drag was damaged during use. In this case, you’ll need to take it to a certified reel repair shop to have it repaired or replaced.

Most Common Causes For Baitcaster Drag to Not Working Properly

Baitcaster Drag Solution

If you’ve ever gone fishing with a baitcaster, you know that one of the most important things is to make sure the drag is set correctly. After all, if the drag isn’t set properly, you could end up losing your fish and it can’t work properly.

So, what can cause a baitcaster’s drag to not work properly? There are a few different things that can cause this:

1. The bail spring could be damaged or not working correctly. This is the spring that helps keep the bail in the correct position. If it’s not working correctly, it can cause the drag to not work properly.

2. The bearings could be old or damaged. The bearings help the reel spin smoothly, and if they’re not working correctly, it can cause the drag to not work properly.

3. There could be corrosion on the reel. This can cause the drag to not work properly.

4. The reel could be over-lubricated. This can cause the drag to not work properly.

5. The level wind could be broken. The level wind is what helps keep the line in place. If it’s not working correctly, it can cause the drag to not work properly.

6. The line could be slipping. This can cause the drag to not work properly.

7. The line size could be wrong. If the line is too small or too large, it can cause the drag to not work properly.

8. There could be backlash. This is when the line gets tangled. If there’s a backlash, it can cause the drag to not work properly.

9. The reel could be worn out. This can cause the drag to not work properly.

If you’re having trouble with your baitcaster’s drag, it’s important to figure out what’s causing the problem. Once you know what’s causing the problem, you can fix it and get back to fishing.

Also, read the best Baitcaster setup for bass fishing in2022.

How to Fix These Issues?

To fix these issues, you’ll need to:

  • Check the bail spring and make sure it’s not damaged.
  • Check the bearings and make sure they’re not old or damaged.
  • Clean off any corrosion that’s on the reel.
  • Make sure the reel isn’t over-lubricated.
  • Check the level wind and make sure it’s not broken.
  • Check the line and make sure it’s not slipping.
  • Check the line size and make sure it’s the right size.
  • Get rid of any backlash.
  • If the reel is worn out, replace it.

FAQs:

Why is the drag on my reel not working?

The most common reason for a drag not to work is that the spool is not fully seated in the reel. To fix this, first, make sure that the spool is correctly installed in the reel. If it is, then try tightening the spool screw.

If the drag still does not work, then the problem may be with the drag washers. These washers can become dry and sticky over time, which can cause the drag to not work correctly. To fix this, simply clean the drag washers with a mild soap and water solution.

How do I fix the drag on my baitcaster?

The most common cause of drag problems on baitcasting reels is poor lubrication. To fix this, remove the spool and clean it thoroughly with a degreaser. Then, apply a thin layer of reel oil to the spool shaft and gears. Finally, reassemble the reel and test it out.

Why won’t my drag tighten on my baitcaster?

If your drag won’t tighten on your baitcaster, likely, the spool is not seated correctly. To fix this, first, make sure that the spool is correctly seated in the reel. If it is not, unscrew the spool and reseat it. Once the spool is seated correctly, try tightening the drag again. If it still won’t tighten, there may be something wrong with the drag itself and you may need to take it to a baitcaster repair shop.

What should drag be set at for Baitcaster?

It will vary depending on the type of baitcaster you are using, the type of fish you are trying to catch, and the conditions of the water. However, as a general rule of thumb, most anglers will set the drag on their baitcaster at around 25% of the line’s rated breaking strength.

Does drag affect casting?

Yes, drag does affect casting. The amount of drag will determine how far your line will travel before it hits the water.

How tight should my drag be?

The drag should be tight enough that it does not slip, but not so tight that it is difficult to turn.

Conclusion

After reading this article, it is clear that there are a few things that can be done to fix a baitcaster drag that is not working. First, make sure that the drag is not set too tight. Second, check the washers on the drag to make sure they are not damaged. Finally, make sure the spool is not overfilled.